Jvc RX-6010VBK Manual de usuario

For Customer Use:Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information

7Connecting the Power CordBefore plugging the receiver into an AC outlet, make sure that allconnections have been made.Plug the power cord into an AC

8Basic OperationsThe following operations are commonly used when you play any sound source.Turning the Power On and Off (Standby)On the front panel:To

9Listening Only with HeadphonesYou must turn off speakers when you listen with headphones.1. Connect a pair of headphones to the PHONES jack on the fr

10Adjusting the Subwoofer Output LevelYou can adjust the subwoofer output level if you have selected“YES” for the “SUBWOOFER” (see page 11).Once it ha

11Recording a SourceYou can record any source playing through the receiver to a cassettedeck (or a CD recorder) connected to the TAPE/CDR jacks and th

12Setting the Speakers for the DSP ModesTo obtain the best possible surround sound of the DSP (DigitalSignal Processor) modes (see page 18), you have

13ST SETTINGCrossover Frequency SettingSmall speakers cannot reproduce the bass sound very well. So, ifyou have used a small speaker for any of the fr

14TSETTINGCONTROLDOWN UPDIGITAL 2 terminal settingDIGITAL 1 terminal settingDigital Input (DIGITAL IN) TerminalSettingWhen you use the digital input t

15Storing the Basic Settings andAdjustmentsYou can assign and store different sound settings for each differentplaying source. By using this function,

16Tuning in Stations ManuallyOn the front panel ONLY:1. Press FM/AM to select the band(FM or AM).• Each time you press the button, the bandalternates

Warnings, Cautions and Others/Mises en garde, précautions et indications diverses CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

17FM/AMSelecting the FM Reception ModeWhen an FM stereo broadcast is hard toreceive or noisyYou can change the FM reception mode while receiving an FM

18Using the DSP ModesThe built-in Surround Processor provides two types of the DSP (Digital Signal Processor) mode — Surround mode andDAP (Digital Aco

19Reproducing the Sound FieldThe sound heard in a concert hall or club consists of direct soundand indirect sound — early reflections and reflections

20Available DSP Modes According to the Speaker ArrangementAvailable DSP modes will vary depending on how many speakers are used with this receiver.Mak

2165 – CENTER ++1010 – REAR•R +ENTERMENU98 – REAR•L +1TEST5. Adjust the speaker output levels.• To adjust the center speaker level, pressCENTER +/– (f

22SOUND65 – CENTER +SURROUNDSURROUNDMODECONTROLDOWN UPADJUST SETTINCONTROLDOWN UP+1010 – REAR•R +ENTERMENU98 – REAR•L +TEST TONE L(Left front speaker)

23DSP MODESOUNDMENU98 – REAR•L ++1010 – REAR•R +ENTER4EFFECTSURROUNDSURROUNDMODEAdjusting the DAP ModesOnce you have adjusted the DAP modes, the adjus

24SURROUNDSURROUNDMODESURROUND ON/OFFSURROUND ON/OFFDSP MODEDSP MODEActivating the DSP ModesYou can use only one DSP mode at a time. When a DSP mode i

25COMPU LINK Remote Control SystemThe COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor onthe rece

26Operating JVC’s Audio/Video ComponentsYou can operate JVC’s audio and video components with this receiver’s remote control, since control signals fo

Wall or obstructionsMur, ou obstructionStand height 15 cm or moreHauteur du socle: 15 cm ou plusFrontAvantSpacing 15 cm or moreDégagement de 15 cm ou

27Operating Video ComponentsIMPORTANT:To operate JVC’s video components using this remote control:• Some JVC VCRs can accept two types of the control

28TroubleshootingUse this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVCservice center

29SpecificationsAmplifierOutput PowerAt Stereo operation:Front channels:100 W per channel, min. RMS, driven into 8 Ω,40 Hz to 20 kHz with no more than

30FM tuner (IHF)Tuning Range: 87.5 MHz to 108.0 MHzUsable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)50 dB Quieting Sensitivity: Monaural: 21.3 dBf

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production ofthe wide array of J

LIMITED WARRANTY AUDIO-2JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINALPURCHASER AT

VICTOR COMPANY OF JAPAN, LIMITEDEN0101NHMMDWJEINJVCRX-6010&6018V[J]COVER_f 00.12.5, 1:59 PM2

1Table of ContentsParts Identification ... 2Getting Started ... 3Before Ins

2Parts IdentificationBecome familiar with the buttons and controls on the receiver before use.Refer to the pages in parentheses for details.Front Pane

3Getting StartedThis section explains how to connect audio/video components and speakers to the receiver, and how to connect thepower supply.Before In

4ANTENNAAMLOOPFM 75 COAXIALAMEXT231Snap the tabs on the loop into theslots of the base to assemble theAM loop.Outdoor single vinyl-covered wire (not

5Connecting the subwoofer speakerYou can enhance the bass by connecting a subwoofer.Connect the input jack of a powered subwoofer to theSUBWOOFER OUT

6Video component connectionsUse the cables with RCA pin plugs (not supplied).Connect the white plug to the audio left jack, the red plug to theaudio r